Comrades: Can anyone identify this type and if possible where to buy both halves? It has four pins.
I believe it is a KTM HJ/4 but I don't have a Spare Connectors manual that lists it.
jmann
2014-06-23 02:40:00 UTC
ktmguy
2014-06-23 03:07:00 UTC
Have seen it before but don't know what brand.
Did google showed up any answers if you plug the numbers in.
If you know brand I can probably point you to someone who sells them.
Have a play here:
Did google showed up any answers if you plug the numbers in.
If you know brand I can probably point you to someone who sells them.
Have a play here:
Blackduke77
2014-06-23 03:12:00 UTC
I don't recognize that connector but I've always had luck finding connectors at http://www.repairconnector.com
jmann
2014-06-23 04:31:00 UTC
Comrades: I now believe it might be an AMP 114-18063-076 or Tyco and the mating plug might be a F 02U 002 235-01 but I still can't find anywhere that lists these to enable me to buy the mating connector. BERT - help
No. 47
2014-06-23 06:30:00 UTC
Check the US spec part fiche - it's for an unused emissions control system on the Uk/Australian spec versions and sits unconnected in the headstock area.
ktmguy
2014-06-23 08:33:00 UTC
Post missing.
jmann
2014-06-23 08:52:00 UTC
Comrades: Oh I know exactly what it's for and where it is - it is a Bosch device I'm reticent to cut the harness as there is not much room. The Bosch data sheet says that one can buy the mating part, but from where?
ktmguy
2014-06-23 08:55:00 UTC
Post missing.
Superdan
2014-06-23 09:41:00 UTC
I have the male Bosch connector from a spare (knackered) wiring loom I have for the Tuono V4, I cut off all the connectors, will take a look in the garage.
Ah, just had a look its the same part you have pictured, not sure if you can buy the female part as it connects to the BOSCH bank angle sensor on my bike.
Ah, just had a look its the same part you have pictured, not sure if you can buy the female part as it connects to the BOSCH bank angle sensor on my bike.
Bert
2014-06-24 06:34:00 UTC
Post missing.
ktmguy
2014-06-24 06:54:00 UTC
Post missing.
No. 47
2014-06-24 09:08:00 UTC
jmann
2014-06-24 10:21:00 UTC
Comrades: Yup did try the Bosch site. Now if Bert can't find it I think I'm going to have to resort to something I haven't done since I was a pimply faced youth (short on money and patience). I think I'm just going to have to resort to knots and insulating tape
Thanks for your help guys I'll proceed but if anyone comes across these connectors it would make me feel better if I didn't have a kludge on the bike.
Thanks for your help guys I'll proceed but if anyone comes across these connectors it would make me feel better if I didn't have a kludge on the bike.
kevxtx
2014-06-24 10:25:00 UTC
Why not re-pin them to another male & female connector. http://www.corsa-technic.com/category.p ... ory_id=107
http://www.ebay.com.au/itm/4-Way-12V-Se ... 2a1511f5f9
http://www.ebay.com.au/itm/4-Way-12V-Se ... 2a1511f5f9
jmann
2014-06-24 10:36:00 UTC
Post missing.
kevxtx
2014-06-24 11:18:00 UTC
You know the deal.
No. 47
2014-06-24 11:54:00 UTC
Jim at http://www.easternbeaver.com? Long shot but he may be able to point you in the right direction if not.