i have just put new mask and clocks on my bike but now i have the alarm led on all the time i dont have a alarm
can this be turned of ?
thanks all
preey
2011-03-14 16:56:00 UTC
samba
2011-03-14 17:20:00 UTC
when I did mine I didn't have any issues with the alarm LED being on... though the dash was completely non-functional when the alarm connector wasn't wired up.
Perhaps you have the two wires crossed? Logically, there are 3 ways you can wire up the 2-pin alarm connector. Correctly (as I had it), not at all (dash no-worky), or crossed. Then again I suppose you may have used the wrong wires to connect the alarm....
Perhaps you have the two wires crossed? Logically, there are 3 ways you can wire up the 2-pin alarm connector. Correctly (as I had it), not at all (dash no-worky), or crossed. Then again I suppose you may have used the wrong wires to connect the alarm....
preey
2011-03-14 17:41:00 UTC
ive just plugged the new loom in to the old loom put the new clocks on done the rev counter mod every thing works
(not done the ecu temp mod yet so tem gage not working yet)
i have a out side temp sensor on order so that will be done asap
ive not done any thing with the alarm dont even no what wires it is ?
but red led is on all the time
(not done the ecu temp mod yet so tem gage not working yet)
i have a out side temp sensor on order so that will be done asap
ive not done any thing with the alarm dont even no what wires it is ?
but red led is on all the time
djfelix
2011-03-14 18:03:00 UTC
Post missing.
preey
2011-03-14 22:20:00 UTC
Bump
any help ?
any help ?
samba
2011-03-15 09:18:00 UTC
Post missing.
preey
2011-03-15 16:10:00 UTC
Post missing.
loony888
2011-03-16 09:48:00 UTC
on your new loom there is a small square plug that looks similar to the indicator plugs, that is where the external temp sensor plugs in.
paul.
paul.
preey
2011-03-16 10:09:00 UTC
Yer so I have the correct one then sensor is on back order so that's that bit sorted
Just need to sort the alarm led now
Thanks
Just need to sort the alarm led now
Thanks
samba
2011-03-16 10:12:00 UTC
have you tried plugging the alarm connectors together yet?
Coming from the clocks, it's the 2 pin connector containing the blue/red wire. And like I mentioned before, the side coming from the bike's main loom should be down in between the hinges. The two connectors probably won't be the same shape/type.
You mentioned you know the two wires I'm on about, but you didn't say which side (clocks loom, or main loom) you meant, so apologies for repeating myself
Coming from the clocks, it's the 2 pin connector containing the blue/red wire. And like I mentioned before, the side coming from the bike's main loom should be down in between the hinges. The two connectors probably won't be the same shape/type.
You mentioned you know the two wires I'm on about, but you didn't say which side (clocks loom, or main loom) you meant, so apologies for repeating myself
preey
2011-03-16 17:38:00 UTC
ok temp sensor on all working its just the led that i need to sort out now but i could live with that
preey
2011-03-16 18:02:00 UTC
Post missing.
djfelix
2011-03-16 18:21:00 UTC
Post missing.
preey
2011-03-16 19:15:00 UTC
samba wrote:
have you tried plugging the alarm connectors together yet?
wear the fooooooooook is it i must be missing sum thing
have you tried plugging the alarm connectors together yet?
wear the fooooooooook is it i must be missing sum thing
samba
2011-03-17 08:25:00 UTC
the 2 pin connector that leads from pin 17 on the main block - with the blue/red cable - is that plugged into a connector that is located right between the hinges of the mask on the end some pretty short wires? i.e. you couldn't pull it further out to fiddle with?
preey
2011-03-17 18:36:00 UTC
Ok i have just taken the clocks of yet again the wire comes out of the clocks like you say and goes in to this plug it plug in to the left hand side then that goes of in the main loom
all the wires from the main clock plug are plugged in i have no lose or spare wires at the back in the mask
all the wires from the main clock plug are plugged in i have no lose or spare wires at the back in the mask
samba
2011-03-18 08:21:00 UTC
hmmm...bizarre... I wont' be able to get into my bike to look/take photos to compare with yourself and David, who both seem to have that plug in the same place. Maybe mine was removed/came loose from the mounting shown in the photo, and is now where I keep describing it (in between the hinges!)
Then again maybe it's a different plug altogether. Mysterious....
I won't be able to get at my bike until next weds I'm afraid....
Then again maybe it's a different plug altogether. Mysterious....
I won't be able to get at my bike until next weds I'm afraid....